| Current File : //etc/nagios/nrpe.cfg |
#############################################################################
# Sample NRPE Config File
# Written by: Ethan Galstad (nagios@nagios.org)
#
# Last Modified: 11-23-2007
#
# NOTES:
# This is a sample configuration file for the NRPE daemon. It needs to be
# located on the remote host that is running the NRPE daemon, not the host
# from which the check_nrpe client is being executed.
#############################################################################
# LOG FACILITY
# The syslog facility that should be used for logging purposes.
log_facility=daemon
# PID FILE
# The name of the file in which the NRPE daemon should write it's process ID
# number. The file is only written if the NRPE daemon is started by the root
# user and is running in standalone mode.
pid_file=/var/run/nrpe/nrpe.pid
# PORT NUMBER
# Port number we should wait for connections on.
# NOTE: This must be a non-priviledged port (i.e. > 1024).
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
server_port=5666
# SERVER ADDRESS
# Address that nrpe should bind to in case there are more than one interface
# and you do not want nrpe to bind on all interfaces.
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
#server_address=127.0.0.1
# NRPE USER
# This determines the effective user that the NRPE daemon should run as.
# You can either supply a username or a UID.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
nrpe_user=nrpe
# NRPE GROUP
# This determines the effective group that the NRPE daemon should run as.
# You can either supply a group name or a GID.
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
nrpe_group=nrpe
# ALLOWED HOST ADDRESSES
# This is an optional comma-delimited list of IP address or hostnames
# that are allowed to talk to the NRPE daemon. Network addresses with a bit mask
# (i.e. 192.168.1.0/24) are also supported. Hostname wildcards are not currently
# supported.
#
# Note: The daemon only does rudimentary checking of the client's IP
# address. I would highly recommend adding entries in your /etc/hosts.allow
# file to allow only the specified host to connect to the port
# you are running this daemon on.
#
#
# NOTE: This option is ignored if NRPE is running under either inetd or xinetd
#allowed_hosts=107.181.182.38,162.255.118.185,185.61.152.136,100.100.255.200,63.250.46.223,198.54.118.134,198.24.166.146,162.0.217.203,185.61.152.244,162.0.218.64,198.177.126.50
allowed_hosts=10.20.223.11,10.23.104.10,10.31.4.10,10.35.5.17,10.27.8.207,10.38.0.10,10.21.3.10,63.250.46.223,100.100.255.200,198.54.118.134,198.177.126.50,185.61.152.136,162.0.217.203,209.74.69.66,10.46.3.10,209.74.73.66,203.161.37.251,10.28.14.10
# COMMAND ARGUMENT PROCESSING
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments to commands that are executed. This option only works
# if the daemon was configured with the --enable-command-args configure script
# option.
#
# *** ENABLING THIS OPTION IS A SECURITY RISK! ***
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow arguments, 1=allow command arguments
dont_blame_nrpe=0
# BASH COMMAND SUBTITUTION
# This option determines whether or not the NRPE daemon will allow clients
# to specify arguments that contain bash command substitutions of the form
# $(...). This option only works if the daemon was configured with both
# the --enable-command-args and --enable-bash-command-substitution configure
# script options.
#
# *** ENABLING THIS OPTION IS A HIGH SECURITY RISK! ***
# Read the SECURITY file for information on some of the security implications
# of enabling this variable.
#
# Values: 0=do not allow bash command substitutions,
# 1=allow bash command substitutions
allow_bash_command_substitution=0
# COMMAND PREFIX
# This option allows you to prefix all commands with a user-defined string.
# A space is automatically added between the specified prefix string and the
# command line from the command definition.
#
# *** THIS EXAMPLE MAY POSE A POTENTIAL SECURITY RISK, SO USE WITH CAUTION! ***
# Usage scenario:
# Execute restricted commmands using sudo. For this to work, you need to add
# the nagios user to your /etc/sudoers. An example entry for alllowing
# execution of the plugins from might be:
#
# nagios ALL=(ALL) NOPASSWD: /usr/lib/nagios/plugins/
#
# This lets the nagios user run all commands in that directory (and only them)
# without asking for a password. If you do this, make sure you don't give
# random users write access to that directory or its contents!
# command_prefix=/usr/bin/sudo
# DEBUGGING OPTION
# This option determines whether or not debugging messages are logged to the
# syslog facility.
# Values: 0=debugging off, 1=debugging on
debug=0
# COMMAND TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# allow plugins to finish executing before killing them off.
command_timeout=60
# CONNECTION TIMEOUT
# This specifies the maximum number of seconds that the NRPE daemon will
# wait for a connection to be established before exiting. This is sometimes
# seen where a network problem stops the SSL being established even though
# all network sessions are connected. This causes the nrpe daemons to
# accumulate, eating system resources. Do not set this too low.
connection_timeout=300
# WEEK RANDOM SEED OPTION
# This directive allows you to use SSL even if your system does not have
# a /dev/random or /dev/urandom (on purpose or because the necessary patches
# were not applied). The random number generator will be seeded from a file
# which is either a file pointed to by the environment valiable $RANDFILE
# or $HOME/.rnd. If neither exists, the pseudo random number generator will
# be initialized and a warning will be issued.
# Values: 0=only seed from /dev/[u]random, 1=also seed from weak randomness
#allow_weak_random_seed=1
# INCLUDE CONFIG FILE
# This directive allows you to include definitions from an external config file.
#include=<somefile.cfg>
# COMMAND DEFINITIONS
# Command definitions that this daemon will run. Definitions
# are in the following format:
#
# command[<command_name>]=<command_line>
#
# When the daemon receives a request to return the results of <command_name>
# it will execute the command specified by the <command_line> argument.
#
# Unlike Nagios, the command line cannot contain macros - it must be
# typed exactly as it should be executed.
#
# Note: Any plugins that are used in the command lines must reside
# on the machine that this daemon is running on! The examples below
# assume that you have plugins installed in a /usr/local/nagios/libexec
# directory. Also note that you will have to modify the definitions below
# to match the argument format the plugins expect. Remember, these are
# examples only!
# The following examples allow user-supplied arguments and can
# only be used if the NRPE daemon was compiled with support for
# command arguments *AND* the dont_blame_nrpe directive in this
# config file is set to '1'. This poses a potential security risk, so
# make sure you read the SECURITY file before doing this.
#command[check_users]=/usr/lib64/nagios/plugins/check_users -w $ARG1$ -c $ARG2$
#command[check_load]=/usr/lib64/nagios/plugins/check_load -w $ARG1$ -c $ARG2$
#command[check_disk]=/usr/lib64/nagios/plugins/check_disk -w $ARG1$ -c $ARG2$ -p $ARG3$
#command[check_procs]=/usr/lib64/nagios/plugins/check_procs -w $ARG1$ -c $ARG2$ -s $ARG3$
# INCLUDE CONFIG DIRECTORY
# This directive allows you to include definitions from config files (with a
# .cfg extension) in one or more directories (with recursion).
include_dir=/etc/nrpe.d/
# plugins in lib64
command[check_load]=/usr/lib64/nagios/plugins/check_load -r -w 1.1,0.9,0.7 -c 1.2,1,0.8
command[check_hdd]=/usr/lib64/nagios/plugins/check_disk -m -w 10% -c 5% -W 10% -K 5% -e -p / -p /tmp
command[check_hdd_backup]=/usr/lib64/nagios/plugins/check_disk -m -w 10% -c 5% -W 10% -K 5% -e -p /backup
command[check_mysql]=sudo /usr/lib64/nagios/plugins/check_mysql
command[check_smtp]=/usr/lib64/nagios/plugins/check_smtp -H localhost -p 25 -t 11
command[check_dns_query]=/usr/lib64/nagios/plugins/check_dig -H 203.161.61.57 -l server1.felltech.net
command[check_crond]=sudo /usr/lib64/nagios/plugins/check_procs -C crond -c 1:
command[check_imap]=/usr/lib64/nagios/plugins/check_imap -H localhost -p 143
# raid card is none
# local plugins
command[check_if_ips]=/usr/local/nagios/plugins/check_if_ips.py 8.8.4.4
command[check_csf]=/usr/local/nagios/plugins/check_csf
command[check_ro_fs]=/usr/local/nagios/plugins/check_ro_fs.sh
command[check_backupage]=sudo /usr/local/nagios/plugins/check_newbackup -v
command[check_puppet]=sudo /usr/local/nagios/plugins/check_puppet -s /opt/puppetlabs/puppet/public/last_run_summary.yaml
command[check_cplicense]=/usr/local/nagios/plugins/check_cplicense
command[check_eximq]=/usr/local/nagios/plugins/check_eximq -w 500 -c 1000
command[check_freemem]=/usr/local/nagios/plugins/check_mem.pl -w 15 -c 10 -f -C
command[check_spamd]=/usr/local/nagios/plugins/check_spamd
command[check_cl_license]=/usr/local/nagios/plugins/check_cl_license
#disabled
#command[check_updates]=/usr/local/nagios/plugins/check_software_updates --no-warn-on-lock -C --all-updates